This is a newer version of the original CK1616 which includes resets on the board so you can use a switch to reset the relay when using toggle mode. This is handy for applications like a garage door where you would want the motor to stop when the door is closed or open all the way.
This 4 channel remote control relay board is available as a kit or assembled unit. The relay board uses "Rolling Code" so it is nearly impossible to crack. Features pre assembled and aligned RF modules, pre assembled key-chain transmitter that only requires you to solder battery clips and case. Receiver requires component mounting & soldering. Receiver can "learn" up to 16 transmitters. Transmitters can be used with multiple receivers. 4 channel output with Single Pole Double Throw (SPDT) relays rated 10A @ 28VDC. Each output can independently be made latching (Push-on/Push-off) or momentary. Range exceeds 50meters. Transmitter uses 12V cell (included). Ideal for higher security garage doors, auto gates, electric locks etc.
Specifications:
Range is over 50 Meters (~150 feet).
Transmits on 433.9 MHz
Transmitter comes fully assembled and includes battery.
Receiver Power 12 VDC (power supply not included).(Need a Power Supply?)
Circuit draws 8mA in idle state, 1 relay energized 44mA, 2 relays 78mA, 3 relays 111mA, and 4 relays 144mA.
Relays have a Common, Normally Closed (NC), and Normally Open (NO).
Each Individual Relay is jumper selectable latching or momentary.
Relay Contact Ratings: 240VAC 7Amps, 125VAC 10Amps, 28VDC 10Amps, (more info on how relays work)
Has 4 resets for each relay.
Includes transmitter and receiver.
Transmitter Dimensions 2-1/4" L x 1-1/2" W x 1/2" H
Receiver Dimensions 3-3/8" L x 3" W x 1" H
This 4 channel remote control relay board is available as a kit or assembled unit. The relay board uses "Rolling Code" so it is nearly impossible to crack. Features pre assembled and aligned RF modules, pre assembled key-chain transmitter that only requires you to solder battery clips and case. Receiver requires component mounting & soldering. Receiver can "learn" up to 16 transmitters. Transmitters can be used with multiple receivers. 4 channel output with Single Pole Double Throw (SPDT) relays rated 10A @ 28VDC. Each output can independently be made latching (Push-on/Push-off) or momentary. Range exceeds 50meters. Transmitter uses 12V cell (included). Ideal for higher security garage doors, auto gates, electric locks etc.
Specifications:
Range is over 50 Meters (~150 feet).
Transmits on 433.9 MHz
Transmitter comes fully assembled and includes battery.
Receiver Power 12 VDC (power supply not included).(Need a Power Supply?)
Circuit draws 8mA in idle state, 1 relay energized 44mA, 2 relays 78mA, 3 relays 111mA, and 4 relays 144mA.
Relays have a Common, Normally Closed (NC), and Normally Open (NO).
Each Individual Relay is jumper selectable latching or momentary.
Relay Contact Ratings: 240VAC 7Amps, 125VAC 10Amps, 28VDC 10Amps, (more info on how relays work)
Has 4 resets for each relay.
Includes transmitter and receiver.
Transmitter Dimensions 2-1/4" L x 1-1/2" W x 1/2" H
Receiver Dimensions 3-3/8" L x 3" W x 1" H
This is a practical power supply for all your projects. Converts AC to DC power. It provides 6 different outputs between 6 and 20VDC @ 500mA. There are also 6 different size jacks to accommodate most projects and two alligator clips just in case there isn't a jack.
Note: This is not a kit, no assembly required.
Specifications:
L: 3-3/4" W: 2-1/2" H: 2-1/2".
Output Voltage: 6, 9, 12, 15, 18 or 20 VDC.
Output Current: Up to 500 mA.
Includes 6 different size jack connectors.
Jack can be reversed from center positive to negative.
Includes alligator clips for projects without power jack.
Includes 9 volt snap type connector
Input: 110VAC
Note: This is not a kit, no assembly required.
Specifications:
L: 3-3/4" W: 2-1/2" H: 2-1/2".
Output Voltage: 6, 9, 12, 15, 18 or 20 VDC.
Output Current: Up to 500 mA.
Includes 6 different size jack connectors.
Jack can be reversed from center positive to negative.
Includes alligator clips for projects without power jack.
Includes 9 volt snap type connector
Input: 110VAC
0 comments:
Post a Comment